Step 4a: Build pib’s shoulder horizontal (Adv)
Tutorial: pib#5 shoulder horizontalPib's shoulder horizontal consists of 17 3D-printed parts and can be assembled in the following 6 steps Make sure to calibrate the Motor first before assembling the shoulder horizontal!This tutorial explains how to assemble each shoulder horizontal, as both use the same parts and follow the same steps |
|
|---|
Overview: Needed Parts
3D Printable Parts:
| Non-printable Parts:
|
|---|
Overview: 3D Printable Parts
C09-Central_rotator_connector
| C65-Bracket_Outer_Shoulder |
|---|---|
C66s-Cap_Front_Outer_Shoulder
| C67-Cap_Back_Outer_Shoulder
|
C68-Inner_Ring_Outer_Shoulder
| C69s-Inner_Part_Outer_Shoulder
|
C70s-Shell_Outer_Shoulder
| C80s-Motor_Housing_Central_Rotator_Shoulder_S
|
C73-Wire-holder-pin
| C74-Wire_holder |
C75-Front_Bracket_Outer_Shoulder
| C76-Shell_cap |
C77s-Central_rotator_motor_connector-shoulder
| C78s-Central_rotator_bracket-shoulder
|
Step-by-Step Tutorial
Step 1: Insert Nuts |
|
Insert 11x S01-M3_nut into the designated slots of C69s-Inner_Part_Outer_Shoulder. Needed Parts: 1x C69s-Inner_Part_Outer_Shoulder, 11x S01-M3_nut |
|
Step 2: Insert Motor for Arm rotation | Difficulty: 1/5 |
Connect the servo cables to E18-STS3095 according to the wiring diagram before placing the motor into C69s-Inner_Part_Outer_Shoulder. Needed Parts: 1x E18-STS3095 |
|
Secure E18-STS3095 with C80s-Motor_Housing_Central_Rotator_Shoulder_S using 2x S06-M3x16 screws and 3x S14-M2.5x6mm Pan Head Screw. Needed Parts: 1x C80s-Motor_Housing_Central_Rotator_Shoulder_S, 2x S06-M3x16, 3x S14-M2.5x6mm Pan Head Screw
|
|
Place the second E18-STS3095 into C69s-Inner_Part_Outer_Shoulder and connect the servo cables. Important: One servo cable must remain available for connection to the servo driver later. Needed Parts: 1x E18-STS3095 |
|
Secure E18-STS3095 using 4x M2.5x10 Cylinder Screw. Needed Parts: 4x M2.5x10 Cylinder Screw |
|
Step 3: Preparing Central_rotator | Difficulty: 2/5 |
Attach C77s-Central_rotator_motor_connector-shoulder to the motor adapter using 4x S14-M2.5x6mm Pan Head Screw. Insert 2x S01-M3_nut into the designated slots. Needed Parts: 1x C77s-Central_rotator_motor_connector-shoulder, 4x S14-M2.5x6mm Pan Head Screw, 2x S01-M3_nut |
|
Attach C09-Central_rotator_connector using 2x M3x8 screws. Needed Parts: 1x C09-Central_rotator_connector, 2x M3x8 screws
|
|
Place 4x M07 and 2x M06 into their designated positions, then position C78s-Central_rotator_bracket-shoulder. Needed Parts: 4x M07, 2x M06, 1x C78s-Central_rotator_bracket-shoulder |
|
Place the assembly into the designated position, attach C70s-Shell_Outer_Shoulder, and secure it using 1x S08-M3x20 screw. Needed Parts: 1x C70s-Shell_Outer_Shoulder, 1x S08-M3x20 |
|
Step 4: Pressfit Ballbearing | Difficulty: 1/5 |
Insert M04-Ballbearing_60x78x10 and C68-Inner_Ring_Outer_Shoulder into C65-Bracket_Outer_Shoulder. Insert 3x S01-M3_nut into the designated slots. Needed Parts: 1x M04-Ballbearing_60x78x10, 1x C68-Inner_Ring_Outer_Shoulder, 1x C65-Bracket_Outer_Shoulder, 3x S01-M3_nut Then repeat this for the other half. |
|
Step 5: Connect outer and inner Shoulder | Difficulty: 2/5 |
Secure the assembly using 4x S08-M3x20 screws. Needed Parts: 4x S08-M3x20 Repeat it for the other side. |
|
Connect both C65-Bracket_Outer_Shoulder parts using 2x S13-M3x40 screws. Needed Parts: 1x C65-Bracket_Outer_Shoulder, 2x S13-M3x40 |
|
Step 6: Finalizing Outer Shoulder |
|
Connect 2x C75-Front_Bracket_Outer_Shoulder to C66s-Cap_Front_Outer_Shoulder using 2x S01-M3_nut and 2x S13-M3x40 screws. Needed Parts: 2x C75-Front_Bracket_Outer_Shoulder, 1x C66s-Cap_Front_Outer_Shoulder, 2x S01-M3_nut, 2x S13-M3x40 |
|
Connect the assembly using 2x S06-M3x16 screws and 9x S13-M3x40 screws. Needed Parts: 2x S06-M3x16, 9x S13-M3x40 |
|
Connect C67-Cap_Back_Outer_Shoulder, C73-Wire-holder-pin, and C74-Wire_holder, and secure them using 2x S06-M3x16 screws. Needed Parts: 1x C67-Cap_Back_Outer_Shoulder, 1x C73-Wire-holder-pin, 1x C74-Wire_holder, 2x S06-M3x16 |
|
Repeat these steps for the second shoulder horizontal |
|
Congratulations! The shoulder horizontal is AssembledE-Mail Support: team@pib.rocks | Discord: discord.gg/GRdpyeDu7P | Web: pib.rocks | Shop: shop.pib.rocks |